OBJECTIVES To obtain a challenging position as an Mechanical/Electrical planner SUMMARY OF QUALIFICATIONS *Over eighteen years experience in the Nuclear Power, Fossil Power and Petrol - Chemical industries. Positions held include: Maintenance Supervisor, Planner, Procedure writer, Motor Operated Valve (MOV) Field Service Technician, Field Service Engineer, Analyst using VOTES,UDS and Viper test equipment, Electrical Motor Overhaul Technician, Medium voltage breaker refurb. And test technician and Electrical Maintenance Technician. Have performed routine maintenance, adjustments, troubleshooting, and overhauls of electric and mechanical power plant equipment, MOV diagnostic testing, work planning using Passport v.6, v.10; E-MPAC and SAP and procedure writing, to include testing, maintenance and operations procedures. TECHNICAL TRAINING AND QUALIFICATIONS MOV Diagnostic Testing (UDS, VIPER, VOTES) qualified (CRANE)*AOV Diagnostic testing Inspections, refurbishment & positioner calibration*MPM diagnostic testing (Liberty)*MOV Refurbishment (Liberty)* Valve Repair Training*Underwater Welding and Construction Certificate (Santa Barbara City College) * Structural Welding (Calif. State)*Medium Voltage breaker overhaul and testing (AVO) * E.Q. splicing (greyboot, Raychem,3M tape)*SOV refurb, replacement and bench testing* WORK HISTORY Mechanical Planner (6/09 to present) Sun Technical Services Planning of work orders for unit 2 completion project, walk down the job, research documents for the correct execution of the work, ensure all hazards are addressed, order parts and materials as required to perform the work. Ensure the design packages conform with TVA and Bechtel policies and Q.A. programs. Watts-Bar Unit 2 Completion Project MOV Testing Oversight (4/09 to 5/09)American Maintenance and Engineering Services Ensure MOV testing is completed as per plant procedures and that all data is collected as specified by Engineering, assist in the installation and operation of the Viper system as required by the craft. St. Lucie Electrical Planner (2/09 to4/09)American maintenance and engineering services Planning of outage work orders for unit 3, walk down the job, research documents for the correct execution of the work, ensure all hazards are addressed, order parts and materials as required to perform the work. Turkey Point Electrical Planner/Procedure writer (6/08 to 11/08) Babcox & Wilcox inc. Perform planning of restart work orders for units 1 & 2, walk down the job, research documents for the correct execution of the work, ensure all hazards are addressed, order parts and materials as required to perform the work. Bruce Power Unit 1&2 Restart Mechanical Planner (3/08 to 6/08) Areva Canada, limited Perform planning of IOP work orders for the running units, walk down the job, research documents for the correct execution of the work, ensure all hazards are addressed, order parts and materials as required to perform the work. Pickering A U-1 Ont. Can. MOV Field Service Engineer (10/07-12/07) Ian Martin limited Pre-outage work order inspection and walk downs. Inspect test equipment to ensure all cal dates are current; all test equipment is available for use and any spare equipment can be accessed easily. Verify all electrical prints are rev checked and available, all valve data sheets for VIPER testing are current and available and all procedures are included in the work order before it is ready to work. Test using VIPER system to satisfy all engineering criteria on 89-10 (safety related valves), analyze test traces as required. Install and remove actuators when needed Pickering A U-1 Ont. Can. Electrical Planner/Assistant P.M. (03/07-10/07) Crane Nuclear Inc. Plan emergent work orders as required verifying that all documentation and support tasks are included, walk down the component to be work and ensure that all support tasks are included in work order. Verify all equipment has arrived and is available for use, Interface with other trades to verify work to be done can be executed at the prescribed time. Ensure all techs are qualified for the work to be performed. Have walkdowns performed to ensure any support activities are in place before the MOV work starts (i.e. Scaffold, insulation removed, etc.), ensure all work in the field is performed safely and to the standards of CRANE Nuclears Quality Assurance Program. Verify work packages are complete before they are handed over to the customer. Bruce A restart, On. Can.
Resume of Richard Lavigne Electrical Planner/Test Tech (02/07-03/07) Crane Nuclear Inc. Pre-outage work order inspection and walk downs. Inspect test equipment to ensure all cal dates are current; all test equipment is available for use and any spare equipment can be accessed easily. Verify all electrical prints are rev checked and available, all valve data sheets for VIPER testing are current and available and all procedures are included in the work order before it is ready to work. Test using VIPER system to satisfy all engineering criteria on 89-10 (safety related valves), analyze test traces as required. Install and remove actuators when needed. Install new control leads as required by work order, verify all control leads are sat by completing resistance check and reland leads per the current wiring diagram Susquehanna N.G.S. MOV night shift lead (10/06-12/06) Crane Nuclear Inc. Pre-outage work order inspection and walk downs. Inspect test equipment to ensure all cal dates are current; all test equipment is available for use and any spare equipment can be accessed easily. Verify all electrical prints are rev checked and available, all valve data sheets for VIPER testing are current and available and all procedures are included in the work order before it is ready to work. Test using VIPER system to satisfy all engineering criteria on 89-10 (safety related valves), analyze test traces as required. Install and remove actuators when needed. San Onofre N.G.S Electrical Planner (9/06-10/06) Crane Nuclear Inc. Pre-outage work order inspection and walk downs. Inspect test equipment to ensure all cal dates are current; all test equipment is available for use and any spare equipment can be accessed easily. Verify all electrical prints are rev checked and available, all valve data sheets for VIPER testing are current and available and all procedures are included in the work order before it is ready to work. D.C.Cook N.S. Electrical tech (1/06-5/06) Crane Nuclear Inc. Pre-outage work order inspection and walk downs. Inspect test equipment to ensure all cal dates are current; all test equipment is available for use and any spare equipment can be accessed easily. Verify all electrical prints are rev checked and available, all valve data sheets for VIPER testing are current and available and all procedures are included in the work order before it is ready to work. Test using VIPER system to satisfy all engineering criteria on 89-10 (safety related valves), analyze test traces as required. Install and remove actuators when needed. D.C.Cook N.S. MOV program lead (5/05-1/06) Crane Nuclear Inc. Per the direction of the shop manager, implement an MOV refurbishment and testing program for refinerys and conventional electrical generation facilities. Write technical reports on issues found during the refurbishment and electrical inspections. Build a database of approximate man hours for any of the work to be done on the MOV (refurb, set limits, P.Ms, removal and installation, etc). Train utility craftsmen in setting limit switches, refurbishment and troubleshooting of M.O.V.s Crane valve services, Benicia, Ca Work Week Director (7/04-5/05) Crane Nuclear Inc. Working with Construction and utility work groups, schedule and track on going and up coming work to coincide with other work group activities that will have an impact on the MOV and AOV testing and refurbishments. Report on status of all work in the morning status meetings, report any road blocks that may hinder progress and report afternoon status for schedule up dates. Pickering N.G.S Pickering, Ont. Can Field Service Engineer (3/04-5/04) Crane Nuclear Inc. Per utility instruction, install test equipment, obtain test data and analyze the data for any anomalies and turnover to Engineering to disposition, if required. Remove and install actuators as required to support valve work. Callaway N.S. MOV Engineer (2/04-3/04) Crane Nuclear Inc. Assist the in house engineering staff with MOV testing and test analysis, determine if the testing is satisfactory and can be turned over to Operations. Brownsferry N.S. Electrical crew Supervisor (01/03 to 02/04) Nebraska Public Power District Plan various types of work orders for Electric shop and Valve team, Verify work orders are ready to work and are complete. Walk down jobs for safety and work hazards. Set up crews for the work of the day, interface with the other shop supervisors, work control, Outage Control center, control room, etc. Verify the crewmembers training is up to date and if training is needed schedule them for it. Set up security access, training and supervise contract technicians during outage along with in-house technicians. Verify with scheduling that the work that is to be scheduled for up coming weeks can be accomplished with the personnel that are available. Give year-end review of the technicians that are in the Electric shop and Valve Team Assist with the work being performed when needed. Cooper Nuclear Station) Previous Work History(Additional work history provided on request)
Education Santa Barbara City College (85-87).....Santa Barbara, California Marine Technology studies including marine biology, seamanship, underwater welding and cutting, mixing of diving gasses, minor electronics, mechanical drawing and hard hat diving, technical writing and report generation. Santa Barbara City College (89-91)Santa Barbara, California Engineering studies including Math, English, Native American Literature and various Engineering Courses. Liberty Technical Services, Inc. (11/92, 7/93) ...... Sacramento, California MOV refurbishment training; parts nomenclature; lubrication types; electrical switch setting and electrical blueprint reading; VOTES Diagnostic System Operation training. Electrical Maintenance Technician Training (4/93)Washington Public Supply System, Washington Basic electrical wire splicing and termination. Raychem and Greyboot solderless connections installation. MOV Maint. and Diagnostic training (8/93, 8/94,6/96) ...Northeast Utilities, Waterford, Conn. MOV Refurb., VOTES & UDS analysis and diagnostic testing, Elect. Wire splicing and terminations. Medium Voltage Breakers (5/98).....AVO/ Multiamp Qualified to overhaul, adjust, and test various types of medium voltage breakers. QA certification upon request INTERNATIONAL CORRESPONDENCE SCHOOLS...Scranton, Pa Completed accredited electricians course, including blueprint reading, crimping, circuit testing, etc. Supervisory training (Interact) ......................................................................................Nebraska Public Power District Completed all required training to become a qualified supervisor. Crane Nuclear (3/97, 1/02)...Kennesaw, Ga. UDS and VIPER diagnostic test system training, diagnostic signature analysis training; Procedure writing and work order planning training using Passport REFERENCES.Available upon request.
|